Search Results

The safety and comfort of the truck cab, as driver’s location, are significant to the driver, and the white body of the truck cab is an important part of the truck, whose modal and stiffness are directly impact its safety and comfort. Moreover, its modal and stiffness are the key factors that affect the performance of the car, which are also the important indicators that evaluate the ability of preventing fatigue failure and resisting deformation. In order to study whether the modal and stiffness of a truck cab can meet the working requirements, the white body of a truck cab was taken as the research object, and the finite element method (FEM) was chosen to study the modal and stiffness in this paper. The finite element model of the white body of this truck cab was established. The natural frequency and vibration model of white body were obtained by modal analysis. And the lowest frequency of the white body was 22.8Hz, obtained by modal analysis.

A challenge in structural design is the inability to quickly assess how a change in use can affect the structural performance of the system. This is particularly important in the bus industry where there is often multiple variations of one base product type for many customers. Thus for a single design there can be frequent changes to mission profiles or customer constraints, which must be considered within short time periods before production commences for a particular customer. This can often limit full understanding of the structural performance, key structural features or critical failure modes, ultimately limiting the potential for producing buses with minimum structural mass. The proposed method in this paper aims to develop a design tool capable of rapidly informing structural design engineers with respect to the structural limitations of various vehicle components using performance envelopes.

In order to reflect the actual power consumption of logistics electric vehicles in a city, sample real vehicle road data. After preprocessing, the short-stroke analysis method is used to divide it into working blocks of no less than 20 seconds. Based on principal component analysis, three of the 12 characteristic parameters were selected as the most expressive. K-means clustering algorithm is adopted to obtain the proportions of various short strokes, according to the proportion, select the short stroke with small deviation degree to combine, and construct the driving cycle, it has the characteristics of low average speed, high idle speed ratio and short driving distance. AVL-cruise software builds the vehicle model and runs the driving cycle of urban logistic EV. Compared with WLTC, the difference in power consumption is 34.3%, which is closer to the actual power consumption, the areas with the highest motor speed utilization are concentrated only in the idle area.

This SAE Standard applies to the usage of tires of the same nominal size and tread type, but with different outside diameter for articulated front-end loaders. Articulated four-wheel-drive front-end loader performance and component life can be affected by excessive differences in the tire outside circumference and/or diameter. The purpose is to provide specific guidelines for the usage of tires with different outside circumference and/or diameter on articulated front-end loaders.

This SAE Standard applies to the usage of tires of the same nominal size and tread type, but with different outside diameter for articulated front-end loaders. Articulated four-wheel-drive front-end loader performance and component life can be affected by excessive differences in the tire outside circumference and/or diameter. The purpose is to provide specific guidelines for the usage of tires with different outside circumference and/or diameter on articulated front-end loaders.

This SAE Part Standard covers selected metric screws, hex bolts, and nuts manufactured in accordance with American Society for Testing and Materials (ASTM) and SAE fastener standards. This document covers fastener materials often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This document permits the fasteners to be identified and ordered by a part or identifying number (PIN) as defined in this document.

This SAE Part Standard covers selected metric screws, hex bolts, and nuts manufactured in accordance with American Society for Testing and Materials (ASTM) and SAE fastener standards. This document covers fastener materials often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This document permits the fasteners to be identified and ordered by a part or identifying number (PIN) as defined in this document.

This SAE Standard provides a comprehensive list of requirements for the selection, identification, and control of metric and inch sized fasteners for use in shipboard applications for both shipbuilder installed joints and for use in shipboard components. The fastener selection requirements include the following: a Materials b Thread selection c Plating, coatings, and surface treatments d Locking devices and elements e Screw thread fastener inserts f Fastener part or identifying numbers g Identification markings

Although not limited to, these installations are normally used on trucks considered as Medium Duty (Class 6 and 7), as well as Heavy Duty (Class 8).

This Hydrospace Information Report (HIR) identifies the general environmental considerations for the design, development, evaluation, and testing of advanced surface craft, submersible vehicles, and other marine craft. This HIR provides criteria on the environmental limits within which marine vehicles, related components, and associated equipment should operate satisfactorily and reliably.

A numerical simulation model for predicting the fuel hydrocarbon permeation as well as the barrier layer thickness optimization for multilayer plastic fuel tanks is presented. The diffusion model is based on Fick's laws of diffusion for a steady/unsteady state permeation regime through a multilayer polymeric wall under isothermal condition. A continuum approach based on an homogenization technique is used to model solvent diffusion through an n layer film. The hydrocarbon flux determination through the multilayer film is solved using homogenization techniques that ensure continuity of partial pressure at the polymer-polymer inter-diffusion interface. Since the pinch-off zone is known to be the major source of emission per unit area, a method has been developed to automatically detect it at the end of the extrusion blow molding process and the diffusion model is adapted to adequately evaluate the hydrocarbon permeation through this specific area.

The conventional rear tandem axle of a three-axle vehicle produces a yaw resisting moment that adversely impacts vehicle performance. This work examines the effect of steering the rear axle on tire wear. Using actual vehicle test data, a tire wear model is developed. This tire wear model is then used to predict tire wear savings over an actual commercial vehicle duty cycle when the rear axle is steered. The result of this projection is shown to be consistent with reported third party field experience.

The temperature distribution is studied theoretically in a battery module stacked with 12 high-power Li-ion pouch cells. The module is cooled indirectly with ambient air through aluminum heat-sink plates or cooling plates sandwiched between each pair of cells in the module. Each of the cooling plates has an extended cooling fin exposed in the cooling air channel. The cell temperatures can be controlled by changing the air temperature and/or the heat transfer coefficient on the cooling fin surfaces by regulating the air flow rate. It is found that due to the high thermal conductivity and thermal diffusivity of the cooling plates, heat transfer of the cooling plate governs the cell temperature distribution by spreading the cell heat over the entire cell surface. Influence of thermal from the cooling fins is also simulated.

Ideal operation temperatures for Li-ion batteries fall in a narrow range from 20°C to 40°C. If the cell operation temperatures are too high, active materials in the cells may become thermally unstable. If the temperatures are too low, the resistance to lithium-ion transport in the cells may become very high, limiting the electrochemical reactions. Good battery thermal management is crucial to both the battery performance and life. Characteristics of various battery thermal management systems are reviewed. Analyses show that the advantages of direct and indirect air cooling systems are their simplicity and capability of cooling the cells in a battery pack at ambient temperatures up to 40°C. However, the disadvantages are their poor control of the cell-to-cell differential temperatures in the pack and their capability to dissipate high cell generations.

A cyclically pressurized hydraulic component made of compacted graphite iron (CGI) is examined in fatigue design. This CGI component has a notch, formed at the intersection of two drilling channels. This notch causes the stress to be locally elevated and may potentially serve as a fatigue initiation site. Traditional fatigue design approaches calculate the maximum stress/strain range acting at the notch and apply the Neuber correction when calculating fatigue life. It is, however, found that the fatigue life is dramatically underestimated by this method. This prompts the use of the critical distance method because the stresses are concentrated in a relatively small volume. When using the critical distance method, the fatigue life is correctly predicted. Finally, a fracture mechanics model of the crack check the reasonableness of the critical distance method results.

Durability and reliability performance is one of the most important concerns of a recently developed Thermal Regeneration Unit for Exhaust (T.R.U.E-Clean®) for exhaust emission control. Like other ground vehicle systems, the T.R.U.E-Clean® system experiences cyclic loadings due to road vibrations leading to fatigue failure over time. Creep and oxidation cause damage at high temperature conditions which further shortens the life of the system and makes fatigue life assessment even more complex. Great efforts have been made to develop the ability to accurately and quickly assess the durability/reliability of the system in the early development stage. However, reliable and validated simplified engineering methods with rigorous mathematical and physical bases are still urgently needed to accurately manage the margin of safety and decrease the cost, whereas iterative testing is expensive and time consuming.

Fatigue, creep, oxidation, or their combinations have long been recognized as the principal failure mechanisms in many high-temperature applications such as exhaust manifolds and thermal regeneration units used in commercial vehicle aftertreatment systems. Depending on the specific materials, loading, and temperature levels, the role of each damage mechanism may change significantly, ranging from independent development to competing and combined creep-fatigue, fatigue-oxidation, creep-fatigue-oxidation. Several multiple failure mechanisms based material damage models have been developed, and products to resist these failure mechanisms have been designed and produced. However, one of the key challenges posed to design engineers is to find a way to accelerate the durability and reliability tests of auto exhaust in component and system levels and to validate the product design within development cycle to satisfy customer and market's requirements.

Mechanical and thermal properties of the rubber compounds of a tire play an important role in the overall performance of the tire when it is in contact with the terrain. Although there are many studies conducted on the properties of the rubber compounds of the tire to improve some of the tire characteristics, such as the wear of the tread, there are a limited number of studies that focused on the performance of the tire when it is in contact with ice. This study is a part of a more comprehensive project looking into the tire-ice performance and modeling. In this study, to understand the effect of different rubber compounds on the tire performance, three identical tires from the same company have been chosen. The tires’ only difference is the material properties of the rubber. Two approaches have been implemented in this study.

Abstract As electric vehicles (EVs) begin to increase their market share in the transport sector, the efficiency of battery packs becomes critical to their performance. Within large battery packs, cell variations occur due to manufacturing processes but can also become prominent during operation due to ineffective thermal management and accelerated degradation of some cells. A battery management system (BMS) will generally account for variations in state of charge (SOC) for cells in series through balancing, but conventional BMSs do not tend to consider the imbalances of cells in parallel as their SOCs should eventually converge themselves. This can, however, lead to cells experiencing higher currents and therefore increased degradation compared to other cells within the pack.

Abstract Off-highway equipment are subjected to diverse environmental conditions, severe duty cycles, and multiple simultaneous operations. Due to its continuous, high-power adverse operating conditions, equipment are exposed to high thermal loads, which result in the deterioration of its performance and efficiency. This article describes a model-based system simulation approach for thermal performance evaluation of a self-propelled off-highway vehicle. The objective of developing the simulation model including thermal fidelity is to quantify the impact of thermal loads on vehicular system/subsystems performance. This article also describes the use of simulation models for driving architectural design decisions and virtual test replication in all stages of product development.